manualshive.com logo in svg

Fujitsu DL9300, User Manual

Share
Download
Fujitsu DL9300 User Manual Download Page 126

Setup Mode

USING SETUP MODE

User's Manual

5-35

CONFIGURATION ITEMS
AND OPTIONS

The CONFIG function defines the printer’s primary configuration.
You can set the following options to ensure that the printer meets
your requirements:

• Tear off for continuous forms
• Autoloading of single sheets
• Direct decoding of certain commands
• Settings for feeding, printing and ejecting

Table 5.6 describes the CONFIG items and options.  Items are listed in
the order they are printed.  The procedure for changing the options is
reffered to 

Setup Mode Example

.

Table 5.6  CONFIG Items and Options

NOTE:  Underlined options are the factory defaults.

CONFIG Items

Options

Description

<TEAROFF>

Auto or manual tearoff feed.

MANUAL

Automatic tearoff feed is invalid,
and tearoff feed must be done using
the TEAR OFF button.

AUTO

Automatic tearoff feed is valid but
only for continuous forms.  Tearoff
feed can also be done using the
TEAR OFF button.

<TEARPOS>

Tearoff position.

VISIBLE

Select this option when your
software positions forms to the next
top-of-form after printing the last
data.  The printer performs tearoff
feed without adding a form feed
when data transfer has stopped.

ALWAYS

Select this option when your soft-
ware stops after printing the last
data.  The printer performs tearoff
feed after adding a form feed when
data transfer has stopped.

Summary of Contents for DL9300



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands