manualshive.com logo in svg

Fujitsu DL9300, User Manual

Share
Download
Fujitsu DL9300 User Manual Download Page 16

Introduction

1-1

INTRODUCTION

User's Manual

1

INTRODUCTION

Congratulations on purchasing this printer.

  This

printer is a compact, versatile, flat paper path
printer that offers maximum compatibility with
 today’s software packages and personal computers.
The 24-wire print head provides crisp, clear printing for business,
office, and home environments.  This printer is also easy to install and
use.

Dot matrix printer

Key printer features and options are listed in the next two sections.

• Software compatibility

.  This printer, which operates primarily

with the Fujitsu DPL24C PLUS command set, is compatible with
the IBM Proprinter XL24E command set and the Epson ESC/P2
command set.

• Various character sets

.  As basic character sets, IBM PC character

sets 1 and 2 are available for the Fujitsu DPL24C PLUS command
set and the IBM Proprinter XL24E emulation, and the italic charac-
ter set and graphics character sets 1 and 2 are available for the
Epson ESC/P2 emulation.  As national character sets, a total of 56
or 58 national character sets (depending on the emulation), includ-
ing IBM PS/2 character sets, are available.

FEATURES

Summary of Contents for DL9300



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands