FujiFilm PXG4, Operation Manuals

Page: 133 / 158

– 132 –
13
Chapter
Overview of Password Setup
(Ch11)
The password function allows you to hide displays by
block (multiple channels).
Blocks set not to display can be changed by entering
monitoring mode and inputting the password (PASS) to
display the channels included in those blocks.
There are fives types of password settings: "PAS1", "PAS2",
"PAS3", "Super PASS", and "Special PASS".
●
: Displayed when the password is entered.
× : Not displayed, even when the password is entered.
Factory settings for passwords are as follows:
Refer to
See "Monitor Mode" (p. 13) for more information about entering
passwords
Channel Menu Password
Channel Display Contents PAS1 PAS2 PAS3
Super
PASS Special
PASS
Ch1 "
ooo oPPPPEEEE
" Operation
Parameters
● ● ● ● ●
Ch2 "
PPP Piiiidddd
" Control (PID)
Parameters
● ● ● ● ●
Ch3 "
PPP PLLLLTTTT
" PID Palette
Parameters
×
● ● ● ●
Ch4 "
PPP PrrrrGGGG
" Ramp/Soak
Parameters
×
● ● ● ●
Ch5 "
MMM Moooonnnn
" Monitor
Parameters
× ×
● ● ●
Ch6 "
SSS SEEEETTTT
" Setup Parameters × ×
● ● ●
Ch7 "
SSS
SyyyySSSS
" System
Parameters
× ×
● ● ●
Ch8 "
AAA
ALLLLMMMM
" Alarm
Parameters
× ×
● ● ●
Ch9 "
CCC
CooooMMMM
" Communication
Parameters
× ×
● ● ●
Ch10 "
PPP
PFFFFbbbb
" Position Feedback
Parameters
× ×
● ● ●
Ch11 "
PPP
PAAAASSSS
" Password
Setup
× ×
● ● ●
Ch12 "
ddd
dSSSSPPPP
" Display Mask for
Each Parameters
× ×
● ● ●
Ch13 "
CCC
CFFFFGGGG
" Environmental
Parameters
× × × ×
●
Point
The channel menu will not appear if the display mask
function is set to not display.
However, dSP (Ch12) will always appear when Super
PASS or Special PASS are entered.
Refer to
See Chapter 14 “Display Mask for Each Parameter (Ch12)“
(page 133) for an explanation of the display mask function.
Password
Type PAS1 PAS2 PAS3 Super
PASS
Special
PASS
Password 0000 0000 0000 FEFE F1C0
Caution
Special PASS or Super PASS passwords cannot be changed.
Enter the above passwords to display channel 13 (config) to set
parameters.
Passwords 1 to 3
to
This section explains how to set passwords.
Range: 0000 to FFFF
Steps for Setting the Password
The following steps explain how to set passwords by using
PAS2 = 1234 as an example.
1
Press and hold the key to display the setup
mode channel menu ("
ooo
oPPPPEEEE CCCChhhh 1111
").
Refer to
See page 127 for information on how to display the
channel menu.
2
Use the keys to select channel 11
("
PPP PAAAASSSS CCCChhhh11111111
").
3
Press and hold the key. "
PPP PAAAASSSS1111
" will appear in
the upper part of the display. Use the
keys to select "PAS2".
4
Press the key, then use the keys to
set "1234", and press the key to confirm the
setting.
5
Press the key to return to the operation mode
PV/SV display.
Operation mode