manualshive.com logo in svg

Fuji Xerox DocuPrint C1110 B, User Manual

Share
Download
Fuji Xerox DocuPrint C1110 B User Manual Download Page 118

118

6 Troubleshooting

Reload Manual
Feeder

The paper is not loaded correctly in the manual feeder. Remove the paper and load it 
again.
After loading the paper, the [Press SET to Continue] message appears. Press the 
<Eject/Set> button on the control panel to start printing.
If the <Eject/Set> button is not pressed for 5 seconds, the printer will start printing 
automatically.

Refer to

• " Loading Paper in the Manual Feeder" (P. 75)

Remove Drum 
Cartridge Tapes

The yellow tapes are not removed from the drum cartridge.
Remove the drum cartridge from the printer, completely pull out the yellow tapes 
from the side of the cartridge, and then reinstall it to the printer.

Remove paper
from Manual Feed

Remove the paper from the manual feeder.

Remove & Shake
Toner Cart [X]

(X: Y, M, C, or K)

This message appears when the output color for the X toner cartridge is light.
Remove the X toner cartridge from the printer and shake the toner cartridge. This 
may solve the problem.

Replace Drum
Cartridge

It is time to replace the drum cartridge.
Replace the drum cartridge.

Refer to

• " Replacing the Drum Cartridge" (P. 129)
• "Types of Consumables" (P. 124)

Replace Fuser
Unit in Place

 

Then Reboot
Printer

It is time to replace the fuser unit.
Replace the fuser unit.

Refer to

• " Replacing the Fuser Unit" (P. 132)
• "Types of Consumables" (P. 124)

Replace Toner
Cartridge [X]

(X: Y, M, C, or K)

The X toner cartridge has run out of toner, or the waste toner box becomes full.
Replace the X toner cartridge.

Refer to

• "Replacing the Toner Cartridges" (P. 127)
• "Types of Consumables" (P. 124)

Set Fuser Unit
in Place

 

Then Reboot
Printer

The fuser unit is not installed correctly. 
Switch the power off, and then reinstall the fuser unit. 

SET to print
CANCEL to Abort

To print the job, press the <Eject/Set> button, or to cancel the job, press the <Cancel 
Job> button on the control panel.

SysError ***-***
Press SET

A system error occurred.
Copy down the error code (***-***) on the display, and contact our Customer Support 
Center or your dealers.
Pressing the <Eject/Set> button on the control panel clears the error.

Note

• If the six-digit number (***-***) is “016-739” or “016-740”, the network expansion 

card (optional) may not be installed correctly. Reinstall the network expansion card 
to the printer and try printing again.

SysError ***-***
Reboot Printer

The printer may be at fault.
Switch the power off, wait for the display to go out, and switch the power back on 
again. If the same error code is displayed, copy down the error code (***-***), and 
contact our Customer Support Center or your dealers. 

Refer to

• "Network-related Problems (DocuPrint C1110 only)" (P. 120)

Message

Symptom/Cause/Remedy

Summary of Contents for DocuPrint C1110 B


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands