Fuji Xerox DocuPrint C1110 B User Manual Download | Manualshive

Page: 110 / 209

background image

110

6 Troubleshooting

Texts are smeared.

The paper is not appropriate for the printer. Load appropriate paper.

Refer to

• "Supported Paper" (P. 70)

The paper is damp. Load fresh paper.

Dew condensation may have formed in the printer.
On the control panel, set the interval that the printer switches to the Sleep mode to
more than 60 minutes, and let the printer stand with its power on. After about an hour,
the condensation disappears due to the heat inside the printer.

Refer to

• Sleep mode: " System Settings" (P. 90)

Color around the edge of texts
is incorrect.

The color registration is incorrect.
Adjust the color registration on the control panel.

Refer to

• "7.9 Adjusting the Color Registration" (P. 161)

Printed image or texts wear off
quickly.
Double printing with
appropriate margins

The fuser temperature may not be set properly. Adjust the fuser temperature on the
control panel.

Refer to

• "7.11 Adjusting the Fuser Temperature" (P. 166)

Ghost

The drum cartridge is damaged or deteriorated. The drum cartridge may need
replacement depending on its condition. Contact our Customer Support Center or your
dealers.

Refer to

• "Replacing the Drum Cartridge" (P. 129)

The image transfer voltage (the [Adjust BTR] setting on the control panel) may not be
set properly.
Adjust the transfer voltage on the control panel.

Refer to

• "7.10 Adjusting the Image Transfer Voltage" (P. 165)

Strip-shaped, uneven halftone
image

The light fatigue may have been occurred in the drum cartridge. The light fatigue is
caused by exposing the drum cartridge to light while leaving the front cover open.
Perform the drum cartridge refreshing under [Maintenance mode] on the control panel.

Refer to

• "7.14 Drum Cartridge Refreshing" (P. 169)

Symptom

Cause/Remedy

«
...
108
109
110
111
112
...
»

Summary of Contents for DocuPrint C1110 B


















































































































































































































Reviews:

No comments

Related manuals for DocuPrint C1110 B

Brand: idp Pages: 88

Brand: Oki Pages: 207

Brand: Oki Pages: 56

Brand: Oki Pages: 6

Brand: Oki Pages: 8

Brand: Oki Pages: 16

Brand: Oki Pages: 323

Brand: Oki Pages: 36

Brand: Oki Pages: 150

Brand: Oki Pages: 341

Brand: Oki Pages: 177

Brand: Oki Pages: 162

Brand: Oki Pages: 20

Brand: Oki Pages: 104

Brand: Oki Pages: 168

Brand: Oki Pages: 28

C9600hnColorSignage

Brand: Oki Pages: 20

C9600hnColorSignage

Brand: Oki Pages: 125

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands