manualshive.com logo in svg

Fuji Xerox DocuPrint C1110 B, User Manual

Share
Download
Fuji Xerox DocuPrint C1110 B User Manual Download Page 109

6.4 Print Quality Problems

109

Output is partially blanked-out.
Vertical white streaks appear 
on output.

The paper is not appropriate for the printer. Load appropriate paper.

Refer to

• "Supported Paper" (P. 70)

The paper is damp. Load fresh paper.

The toner cartridge is not installed correctly.
Correctly install the toner cartridge.

The interior of the printer may not be clean. Remove the drum cartridge from the printer, 
and place it in a dark place. Check the light path, and then remove the shielding.

Dew condensation may have formed in the printer.
On the control panel, set the interval that the printer switches to the Sleep mode to 
more than 60 minutes, and let the printer stand with its power on. After about an hour, 
the condensation disappears due to the heat inside the printer.

Refer to

• Sleep mode: " System Settings" (P. 90)

The drum cartridge or fuser unit is damaged or deteriorated. The drum cartridge or 
fuser unit may need replacement depending on its condition. Contact our Customer 
Support Center or your dealers.

White patches appear on 
output.
Toner scatters around images.
Images are bluish.

The image transfer voltage (the [Adjust BTR] setting on the control panel) may not be
set properly.
Adjust the transfer voltage on the control panel.

Refer to

• "7.10 Adjusting the Image Transfer Voltage" (P. 165)

Change the [Paper Type] setting and try printing again. For example, if [Paper Type] is
set to [Plain Paper], try changing it to [Bond Paper] or [Recycled Paper]. If it is set to
[Heavyweight 1], try changing it to [Heavyweight 2].

Symptom

Cause/Remedy

light path

Summary of Contents for DocuPrint C1110 B


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands