Fronius Virtual Welding Operating Instructions Manual Download Page 114 | Manualshive

Page: 114 / 168

background image

114

NOTE!

Press the red Setup key to open the Setup menu on older systems with no sensor:

►

Press once = access the Setup menu

►

Press twice = calibrate touchscreen

Depending on whether the authorisation card belongs to an administrator or a user, this
opens either the full setup menu for administrators or a simplified setup menu for users.

The restricted range of settings that is available to users is described separately in the sec-
tion below.

Detailed information about adding and removing authorisation cards can be found in the
section "Other Settings menu item" under "Sensor registration".

An "Administrator" authorisation card will open the "Setup" window:

The following sections contain detailed explanations of the menu items.

Restricted settings for users:
users are only able to select the following menu items:
-

"Other settings"

-

"Technical settings"

«
...
112
113
114
115
116
...
»

Summary of Contents for Virtual Welding









































































































































































Reviews:

No comments

Related manuals for Virtual Welding

Brand: Harman Kardon Pages: 2

Brand: L-Acoustics Pages: 98

Brand: BST Pro Pages: 9

Soundmaster 138

Brand: SOUNDMASTER Pages: 1

Brand: cias Pages: 80

Brand: Audiocenter Pages: 40

NeverFreeze SX-0810-24

Brand: ThermoSoft Pages: 5

Brand: Elk Products Pages: 3

ATT COMBI LIFT 4.40 S

Brand: Nussbaum Pages: 260

Brand: Roadstar Pages: 23

Brand: Monacor Pages: 10

Brand: SensoIRIS Pages: 2

Brand: Lorex Pages: 14

Brand: Miller Pages: 56

Brand: WARPP Pages: 23

Brand: Motorola solutions Pages: 52

Brand: Neutec Pages: 22

Brand: Daewoo Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands