Friedrich Floating Air Pro-Premiere FPHFW18A3A Service Manual Download Page 49

Page: 49 / 94

TROUBLESHOOTING

Diagnostic Codes
Led Display

Error
Code

Power Timer

Running

Content

The root cause is may be one of the following

Normal

BLINK

The failure for temperature

sensor of outdoor coil

a. The outdoor temperature sensor loose.

b. The outdoor temperature sensor failed.

c. The indoor control board failed

BLINK

OFF

Compressor exhaust

temperature sensor in

trouble

a. the compressor exhaust temperature sensor connect

loose.

b. the compressor exhaust temperature sensor failed.

c. the outdoor control board failed.

BLINK

OFF

IPM module protection

a.The IPM board failed.

b.The outdoor fan is broken.

c.The outdoor fan motor failed

d.The outdoor fan has been blocked.

e.The condenser is dirty.

f.The outdoor unit has been installed below standards.

OFF

BLINK

OFF

AC voltage higher or lower

protection

a. the supply voltage is higher or lower than normal.

b. the inner supply voltage of the unit is higher or lower

than normal.

OFF

Communication failure

between the indoor unit

and outdoor unit

a.the communication cable connect loose.

b.the communication cable failed.

c.the connection between the filter board and the

outdoor control board is incorrect or loose.

d.the connection between the filter board and the

terminal is incorrect or loose.

e.the indoor control board failed.

f.the PFC board failed.

g.the power board failed.

h.the outdoor control board failed.

Current overload protection a.the fan motor runs abnormally.

b.the condensor and evaporator are dirty.

c.the air inlet and outlet is abnormal or obstructed.

Maximum current

protection

a.the outdoor control board is short circuited.

b.the drive board is short circuited.

c.ther components are short circuited.

OFF

Communication trouble

between outdoor unit and

driver

a. the connection wires connector loose.

b.the outdoor board or drive board failed.

BLINK

OFF

Outdoor EEPROM in trouble

a.the EEPROM chip is loose;

b.the EEPROM chip inserted in the opposite direction.

c.the EEPROM chip failed.

Outdoor ambient

temperature too low

protection

Outdoor ambient temperature too low.

BLINK

OFF

Compressor exhaust

temperature too high

protection

a.the compressor exhaust temperature sensor failed

b.the refrigerant chage is low.

BLINK

Outdoor ambient

temperature sensor in

trouble

a.the outdoor ambient temperature sensor connector

is loose.

b.the outdoor ambient temperature sensor failed.

c.the outdoor control board failed.

OFF

BLINK ON

Compressor shell

temperature too high

protection

a.the compressor exhaust temperature sensor

connector loose.

b.the refrigerant charge is low.

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A































































































Search results

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A

Reviews:

Related manuals for Floating Air Pro-Premiere FPHFW18A3A

Brands by name

Popular brands

Friedrich Floating Air Pro-Premiere FPHFW18A3A, Service Manual

Search results

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A

Reviews:

Related manuals for Floating Air Pro-Premiere FPHFW18A3A

Brands by name

Popular brands