Friedrich Floating Air Pro-Premiere FPHFW18A3A Service Manual Download Page 50

Page: 50 / 94

TROUBLESHOOTING

Diagnostic Codes

LED Display

Error
Code

Power Timer

Running

Content

The root cause is may be one of the following

OFF

Anti-freeze protection

with cooling or overload

protection with heating in

a.the indoor coil temperature sensor connector loose.

b.the indoor coil temperature sensor failed.

c.the indoor control board failed.

d. the refrigerant system is abnormal.

OFF

PFC protection

a.the PFC failed.

b.the outdoor drive board failed.

OFF

DC compressor start

failure

a.the outdoor drive board failed.

b.the compressor failed.

OFF

BLINK

Compressor drive in

trouble

a.the outdoor drive board failed.

b.the compressor failed.

c. the outdoor control board failed.

OFF

BLINK

Outdoor fan motor locked

rotor protection

a.the connection of the outdoor fan motor is loose.

b.there are something blocking the outdoor fan.

c.the fan motor failed.

d.the outdoor control board failed.

OFF

BLINK

Outdoor coil anti-overload

protection with cooling

a.the refrigerant charge is exxcessive.

b.the outdoor fan motor failed.

c.the outdoor fan is broken.

d.the condensor is dirty.

e.the air inlet and air outlet of the indoor unit and the

outdoor unit are abnormal.

Compressor pre heating

process

it is normal mode in cold weather

Expansion valve A tube

(thin) sensor fault

1. The wiring of the sensor for the expansion valve A

(thin tube) connect loose;

2. The sensor for the expansion A(thin tube) has failure;

3. The sampling circuit is abnormal.

Outdoor board chip failure.

a.Using the wrong drive board;

b.Using the wrong compressor.

Overheated outdoor

radiator

a. Radiator sensor fails.

b. Detection circuit of the sensor on the control panel

fails.

Protection against too high

system pressure

a. The pressure switch fails.

b. The pressure detection switch on the control panel

fails.

c. The measured value of system pressure exceeds the

limit.

BLINK BLINK

Indoor room temperature

sensor failure.

a. The indoor room temperature sensor loose;

b. The indoor room temperature sensor is failure;

c. The indoor control board is failure.

OFF

BLINK BLINK

Indoor coil temperature

sensor failure.

d. The indoor coil temperature sensor loose.

e. The indoor coil temperature sensor failed.

f. The indoor control board failed.

BLINK

Communication failure

between the indoor unit

and outdoor unit

a.the communication cable connector loose.

b.the communication cable failed.

c.the connection between the filter board and the

outdoor control board is incorrect or loose.

d.the connection between the filter board and the

terminal is incorrect or loose.

e.the indoor control board failed.

f.the PFC board failed.

g.the power board failed.

h.the outdoor control board failed.

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A































































































Search results

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A

Reviews:

Related manuals for Floating Air Pro-Premiere FPHFW18A3A

Brands by name

Popular brands

Friedrich Floating Air Pro-Premiere FPHFW18A3A, Service Manual

Search results

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A

Reviews:

Related manuals for Floating Air Pro-Premiere FPHFW18A3A

Brands by name

Popular brands