Friedrich Floating Air Pro-Premiere FPHFW18A3A Service Manual Download Page 60

Page: 60 / 94

TROUBLESHOOTING

Error Code 15

Error 15

Compressor shell temperature

too high protection

Stop the machine for a

while then check the pins

of the protector plug if it

is short or not

Reconnect the plug

Normal protecton,unit

refrigerant charge low, or the

two valves that connecting to

indoor unit are not opening

Yes

The protector fault, replace it.

Or the protector connecting

wire in the conpressor is

loosen, check it

Is the protector plug

connected to the CN902

of the control board

tightly or not

Shell protec

�

on test point:

Fig. 709

Compressor protection device is

open. Wait to see if it resets.

A feel test on compressor should

confirm when cool. If device is

still open, replace device.

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A































































































Search results

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A

Reviews:

Related manuals for Floating Air Pro-Premiere FPHFW18A3A

Brands by name

Popular brands

Friedrich Floating Air Pro-Premiere FPHFW18A3A, Service Manual

Search results

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A

Reviews:

Related manuals for Floating Air Pro-Premiere FPHFW18A3A

Brands by name

Popular brands