Friedrich Floating Air Pro-Premiere FPHFW18A3A Service Manual Download Page 48

Page: 48 / 94

TROUBLESHOOTING

Diagnostic Codes

Indoor Unit

Error
Code

Power Timer

Running Sleep

Content

The root cause is may be one of the following

1. The wiring of the sensor

for the expansion valve A

(thin tube) connect loose;

2. The sensor for the

expansion A(thin tube) has

failure;

3. The sampling circuit is

abnormal.

Outdoor board chip failure.

a.Using the wrong drive board;

b.Using the wrong compressor

Overheated outdoor

radiator

a. Radiator sensor fails.

b. Detection circuit of the sensor on the

control panel fails.

Protection against too high

system pressure

a. The pressure switch fails.

b. The pressure detection switch on the

control panel fails.

c. The measured value of system pressure

exceeds the limit.

BLINK

OFF

The failure for temperature

sensor of indoor room

a. The indoor room temperature sensor loose.

b. The indoor room temperature sensor failed.

c. The indoor control board failed.

BLINK

OFF

The failure for temperature

sensor of indoor coil

temperature

a. The indoor coil temperature sensor loose.

b. The indoor coil temperature sensor failed.

c. The indoor control board failed.

BLINK

OFF

Communication failure

between the indoor unit

and outdoor unit

a. the communication cable connector loose.

b. the connection between the filter board

and the terminal is incorrect or loose.

c. the communication cable failed.

d. the connection between the filter board and

the outdoor control board is incorrect or loose.

e. the indoor control board failed.

f. the PFC board failed.

g. the power board failed.

h. the outdoor control board failed.

BLINK

Indoor EEPROM failure

a. The EEPROM chip loose;

b. The indoor control board failed.

BLINK

OFF

Indoor fan motor runs

abnormally.

a. Something blocking the indoor fan motor.

b. The fan motor cord is disconnected or

loose.

c. The fan motor failed.

d. The indoor control board failed.

BLINK

The failure for Indoor

grounding protection.

The indoor control board failed.

WiFi Connection Enabled

Cycle Power on/off

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A































































































Search results

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A

Reviews:

Related manuals for Floating Air Pro-Premiere FPHFW18A3A

Brands by name

Popular brands

Friedrich Floating Air Pro-Premiere FPHFW18A3A, Service Manual

Search results

Summary of Contents for Floating Air Pro-Premiere FPHFW18A3A

Reviews:

Related manuals for Floating Air Pro-Premiere FPHFW18A3A

Brands by name

Popular brands