Friant Tiles Installation Manual Download Page 7

Page 7

Tiles

 Installation Manual

Stacking Frame Installation

1.  Remove Top Tile at desired location by 

pulling towards you to disengage top 
clips from the Frame, pull Tile up to 
disengage bottom hooks from Frame. 
Repeat for other side of Frame.

2.  Pull Top Cap upward to disengage the 

clips and set aside.

3.  Position Stacking Frame above existing 

Frame, aligning the holes in brackets 
with the holes in the Frame. Install two 
(2) bolts and nut plates provided. Do not 
tighten.

4.  If installing two (2) Stacking Frames side 

by side, install Draw Nut as shown.

5.  Tighten bolts into nut plate.

6.  Reinstall Top Cap on Stacking Frame.

Stacking Frame and Stacking Connector Installation

WARNING: 

Never install Worksurfaces on Stacking Frames.
Never install more than two Stacking Frames on top of each other.
If loading 2-High Stacking Frame, the 900 Corner Stacking Connector 
and adjacent Stacking Frames must be used.

Rectangular Slot

Stacking Frame

Draw Nut

Bolts

Stacking Connector Installation

1.  Remove existing Connector Top Cap and 

Cover and set aside.

2.  Position Stacking Connector on top of exist-

ing Connector, engage Draw Nut into the 
rectangular slots in both the Frame and the 
Connector, and tighten screw.

3.  Install Top Cap onto Stacking Connector.

4.  Install Replacement Cover.

Summary of Contents for Tiles


























Reviews: