Friant Tiles Installation Manual Download Page 3

Page 3

Tiles

 Installation Manual

The Tiles

 System is composed 

of full and/or partial height Walls, 
Support Cabinets, Wall Mounted 
and Free-Standing components, 
and accessories.

The Tiles

 System is consid-

ered to be portable furniture; 
therefore, subject to applicable 
local Fire, Electrical and Building 
Codes. Check with local authori-
ties prior to installation.

Electrical Statement:

Friant’s Tiles

 System Electrical 

Distribution System is listed with 
the Underwriters Laboratories, 
and complies with the National 
Electrical Code, ANSI/BIFMA 70.  
Check with local authorities prior 
to installing the product.

Tiles

 System Installation Manual

Introduction

The Tiles

 System Installation manual provides the necessary instruction for the safe installation of the Tiles

 System for:

• 

The Installers with visual and written instructions.

• 

The End Users to ensure continued safe use of the product when maintaining and reconfiguring the product.

To ensure proper installation of the product, the Tiles

 System requires layout and wall supports as specified in this manual. 

Reconfiguration of the product and additions to an installation must be performed per the instructions in this manual to ensure the 
continued safe use of the product. Friant & Associates, LLC does not assume any responsibility for product that is altered in any way.

WARNING: 

Failure to follow the 
instructions in this manual 
can result in product damage, 
personal injury, or death.

Summary of Contents for Tiles


























Reviews: