Friant Tiles Installation Manual Download Page 4

Page 4

Tiles

 Installation Manual

Tile Assembly, Frames, Connectors, and Change  

of Height Wedge Installation

Notched Tab

Notched Tab

Draw Rod

Draw Rod

Post

Cap Screw

Cap Screw

Frame

Frame

Frames of Equal Heights

1.  Connect Draw Rod to the first frame by 

inserting the bottom hook on Draw Rod 
into rectangular opening at the bottom 
of the frame. Loosen Cap Screw, so it 
lines up with Notched Tab at the top of 
the Frame.

2.  Lift second Frame to engage bottom 

hook on the Draw Rod to the rectangular 
opening at the bottom of the second 
Frame.

3.  Position Frames so that notched Tab 

on one is fitted between shoulders of 
adjacent Cap Screw of Draw Rod. 

NOTE:  Be sure that the Glides are all the 
way in at the bottom of the Frame.  If floor 
is very uneven, Glide adjustment should 
be made during assembly of product. 

4.  Tighten Cap Screw until stiles come 

together.

Frame to Connector of Equal Height

1.  To connect a Frame to a Connector of 

equal height, you need a Draw Rod of 
the same height. 

2.  Connect Draw Rod to the Connector by 

inserting the bottom hook on Draw Rod 
into rectangular opening at the bottom of 
of the Connector. Loosen Cap Screw, so 
it lines up with the Notched Tab at the 
top of the Connector.

3.  Position Frame so that notched Tab on 

the Frame is fitted between shoulders of 
adjacent Cap Screw of Draw Rod. Hold 
Frame against Connector and tighten 
Cap Screw until Frame and Connector 
come together.

Summary of Contents for Tiles


























Reviews: