Friant Tiles Installation Manual Download Page 2

Page 2

Tiles

 Installation Manual

Introduction ...........................................................................................................................................................  3

Tile Assembly, Frames, Connectors, 
and Change of Height Wedge Installation ............................................................................................................  4

Tiles Assembly, Frames, Connectors, and Change of Height Wedge Installation ...............................................  5

Connectors Cover, Finished End Cover, Finished End 
Change of Height Cover, Installation ....................................................................................................................  6

Stacking Frame, and Stacking Connector Installation ..........................................................................................  7

8-Wire Electrical, Base Feed Installation ..............................................................................................................  8

8-Wire Electrical, Base Power Retro, 
and Beltline Power Retro Installation ....................................................................................................................  9

8-Wire Electrical, Beltline Power Retro Duplex Clip Installation ...........................................................................  10

8-Wire Electrical, In-Frame Power Jumper 
and Pass-Through Power Jumper Installation ......................................................................................................  11

8-Wire Electrical, Beltline Power Transfer Installation ..........................................................................................  12

Fabric Tiles, Marker Board Tiles, Perforated Tiles, 
and Window Tiles Installation ...............................................................................................................................  13

Rail Tiles, Power and Data Tiles Installation ........................................................................................................  14

Shelf Ends and Shelf Installation ..........................................................................................................................  15

Flipper Door Unit Door/Cover Installation .............................................................................................................  16

Worksurface Installation .......................................................................................................................................  17

Worksurface Installation .......................................................................................................................................  18

Worksurface Installation .......................................................................................................................................  19

Transaction Surfaces Installation .........................................................................................................................  20

Worksurface Support End Panels, and Half Leg Installation ................................................................................  21

Open Metal Worksurface Support Installation ......................................................................................................  22

Door Frame Installation ........................................................................................................................................  23

Supporting Pedestals and Lateral Files Installation ..............................................................................................  24

Table of Contents

Summary of Contents for Tiles


























Reviews: