manualshive.com logo in svg

Freescale Semiconductor MCF52277, Reference Manual

The Freescale Semiconductor MCF52277 is a powerful microcontroller unit with extensive connectivity options. Ensure optimal usage by downloading the comprehensive Reference Manual for free from manualshive.com. The manual provides detailed instructions and specifications to maximize functionality and performance. User Manual available for download.

Share
Download
background image

DMA Serial Peripheral Interface (DSPI)

MCF52277 Reference Manual, Rev. 1

Freescale Semiconductor

29-3

– General DSPI interrupt (logical OR of the seven above conditions)

•

Modified SPI transfer formats for communication with slower peripheral devices

•

Continuous serial communications clock (DSPI_SCK)

29.1.4

Modes of Operation

The DSPI module has four available distinct modes:

•

Master mode

•

Slave mode

•

Module disable mode

•

Debug mode

Master, slave, and module disable modes are module-specific modes while debug mode is a 
device-specific mode.

Bits in the DSPI_MCR register determine the module-specific modes. Debug mode is a mode that the 
entire device can enter in parallel with the DSPI being configured in one of its module-specific modes.

29.1.4.1

Master Mode

In master mode, the DSPI can initiate communications with peripheral devices. The DSPI operates as bus 
master when the DSPI_MCR[MSTR] bit is set. The serial communications clock (DSPI_SCK) is 
controlled by the master DSPI.

Master mode transfer attributes are controlled by the SPI command in the current TX FIFO entry. The 
CTAS field in the SPI command selects which of the eight DSPI_CTARs sets the transfer attributes. 
Transfer attribute control is on a frame by frame basis. See 

Section 29.4.2, “Serial Peripheral Interface 

(SPI) Configuration

” for more details.

29.1.4.2

Slave Mode

In slave mode, the DSPI responds to transfers initiated by an SPI master. The DSPI operates as bus slave 
when the DSPI_MCR[MSTR] bit is cleared. A bus master selects the DSPI slave by having the slave’s 
DSPI_SS signal asserted. In slave mode, the bus master provides DSPI_SCK. The bus master controls all 
transfer attributes, but clock polarity, clock phase, and numbers of bits to transfer must be configured in 
the DSPI slave for proper communications.

In slave mode, data transfers MSB first. The LSBFE field of the associated CTAR register is ignored.

29.1.4.3

Module Disable Mode

The module disable mode is used for MCU power management. The clock to the non-memory mapped 
logic in the DSPI stops while in module disable mode. The DSPI enters the module disable mode when 
the DSPI_MCR[MDIS] bit is set. See 

Section 29.4.7, “Power Saving Features

,” for more details on the 

module disable mode.

Summary of Contents for MCF52277

































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MCF52277

M-Audio Computer Quick Start Manual preview
Computer
Brand: M-Audio Pages: 10
Yamaha mLAN Driver Manual Book preview
mLAN Driver
Brand: Yamaha Pages: 24
Yamaha DSP1D Supplementary Manual preview
DSP1D
Brand: Yamaha Pages: 5
Paradyne COMSPHERE 3610 User Manual preview
COMSPHERE 3610
Brand: Paradyne Pages: 112
Rolls HR11C Owner'S Manual preview
HR11C
Brand: Rolls Pages: 2
Lindsay Broadband LBON320AC Series Installation And Operation Manual preview
LBON320AC Series
Brand: Lindsay Broadband Pages: 4
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Brand: Softing Pages: 4
IDT Tsi310TM User Manual preview
Tsi310TM
Brand: IDT Pages: 207
Disc Makers Reflex10 User Manual preview
Reflex10
Brand: Disc Makers Pages: 38
XtendLan XL-IPM401 User Manual preview
XL-IPM401
Brand: XtendLan Pages: 21
Ariesys AMK Series User'S Reference Manual preview
AMK Series
Brand: Ariesys Pages: 10
Digital Equipment ChannelWorks Network Installer Manual preview
ChannelWorks
Brand: Digital Equipment Pages: 90
Dinstar UC8000 IPPBX User Manual preview
UC8000 IPPBX
Brand: Dinstar Pages: 103
Advantech EPC-R6410 User Manual preview
EPC-R6410
Brand: Advantech Pages: 70
National Instruments PXI-GPIB Getting Started preview
PXI-GPIB
Brand: National Instruments Pages: 45
Inter-m S- Media Manual preview
S- Media
Brand: Inter-m Pages: 20
DMX4ALL DMX-Relais 2 INRUSH User Manual preview
DMX-Relais 2 INRUSH
Brand: DMX4ALL Pages: 18
Cambium Networks PMP/PTP 450 Series Quick Start Manual preview
PMP/PTP 450 Series
Brand: Cambium Networks Pages: 155

Brands by name

Popular brands

Load more brands