manualshive.com logo in svg

Freescale Semiconductor MCF52277, Reference Manual

The Freescale Semiconductor MCF52277 is a powerful microcontroller unit with extensive connectivity options. Ensure optimal usage by downloading the comprehensive Reference Manual for free from manualshive.com. The manual provides detailed instructions and specifications to maximize functionality and performance. User Manual available for download.

Share
Download
background image

Universal Serial Bus Interface – On-The-Go Module

MCF52277 Reference Manual, Rev. 1

20-78

Freescale Semiconductor

 

20.5.5.6

Miscellaneous Variations from EHCI

20.5.5.6.1

Programmable Physical Interface Behavior

The modules support multiple physical interfaces that can operate in different modes when the module is 
configured with the software programmable physical interface modes. The control bits for selecting the 
PHY operating mode are added to the PORTSC

n

 register providing a capability not defined by the EHCI 

specification.

20.5.5.6.2

Discovery

Port Reset

The port connect methods specified by EHCI require setting the port reset bit in the PORTSC

n

 register for 

a duration of 10 ms. Due to the complexity required to support the attachment of devices not high speed, 
a counter is present in the design that can count the 10 ms reset pulse to alleviate the requirement of the 
software to measure this duration. Therefore, the basic connection is summarized as:

•

Port change interrupt—Port connect change occurs to notify the host controller driver that a device 
has attached.

•

Software shall set the PORTSC

n

[PR] bit to reset the device.

•

Software shall clear the PORTSC

n

[PR] bit after 10 ms.

— This step, necessary in a standard EHCI design, may be omitted with this implementation. 

Should the EHCI host controller driver attempt to write a 0 to the reset bit while a reset is in 
progress, the write is ignored and the reset continues until completion.

•

Port change interrupt—Port enable change occurs to notify the host controller that the device is 
now operational and at this point the port speed is determined.

Port Speed Detection

After the port change interrupt indicates that a port is enabled, the EHCI stack should determine the port 
speed. Unlike the EHCI implementation, which re-assigns the port owner for any device that does not 
connect at high speed, this host controller supports direct attach of non-HS devices. Therefore, the 
following differences are important regarding port speed detection:

•

Port owner hand-off is not implemented. Therefore, PORTSC

n

[PO] bit is read-only and always 

reads 0.

•

A 2-bit port speed indicator field has been added to PORTSC

n

 to provide the current operating 

speed of the port to the host controller driver.

•

A 1-bit high-speed indicator bit has been added to PORTSC

n

 to signify that the port is in HS vs. 

FS/LS. 
— This information is redundant with the 2-bit port speed indicator field above.

Summary of Contents for MCF52277

































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MCF52277

D-Link Express EtherNetwork DFE-670TXD Quick Install Manual preview
Express EtherNetwork DFE-670TXD
Brand: D-Link Pages: 4
DAD DSX 26 User Manual preview
DSX 26
Brand: DAD Pages: 36
D-Link DUB-1320 Quick Install Manual preview
DUB-1320
Brand: D-Link Pages: 2
D-Link DES-1210-08P Manual preview
DES-1210-08P
Brand: D-Link Pages: 15
Omnia 11 Installation And Operation Manual preview
11
Brand: Omnia Pages: 102
Quatech DS-3000 User Manual preview
DS-3000
Brand: Quatech Pages: 27
AMD SB710 User Manual preview
SB710
Brand: AMD Pages: 20
ForeScout CounterACT Quick Installation Manual preview
CounterACT
Brand: ForeScout Pages: 28
Rabbit RabbitCore RCM4400W Product Manual preview
RabbitCore RCM4400W
Brand: Rabbit Pages: 126
Dahua D-NVR4108HS-4KS2/L Quick Start Manual preview
D-NVR4108HS-4KS2/L
Brand: Dahua Pages: 33
Multitech ISI608PC Owner'S Manual preview
ISI608PC
Brand: Multitech Pages: 81
Microcomputer Systems MSI-P602 User Manual preview
MSI-P602
Brand: Microcomputer Systems Pages: 21
ADTRAN DUAL Nx56/64 1200142L1# User Manual preview
DUAL Nx56/64 1200142L1#
Brand: ADTRAN Pages: 48
Ciara Horizon D10750 Disassembly Manual preview
Horizon D10750
Brand: Ciara Pages: 14
Serial Cables PCI-AD-x16HE-BG4 User Manual preview
PCI-AD-x16HE-BG4
Brand: Serial Cables Pages: 18
Abus TVAC21000 User Manual preview
TVAC21000
Brand: Abus Pages: 98
Alphacool GPX-N 1080Ti-M23 Instruction Manual preview
GPX-N 1080Ti-M23
Brand: Alphacool Pages: 4
Crown PIP-ATN Owner'S Manual preview
PIP-ATN
Brand: Crown Pages: 7

Brands by name

Popular brands

Load more brands