FOTEK GD20-004G-2 Operation Manual Download Page 54

Page: 54 / 171

Goodrive20 Series VFD

Function parameter list

-49-

Function

code

Name

Description

Default Modify

P03.10

Current

loop

integral

coefficient I

codes.



The parameters P03.09 and P03.10 are

applicable only to SVC 0 (

P00.00

=0).

Setting range: 0

–65535

1000

○

P03.11

Torque

setting

method

The function code is used to enable the

torque control mode, and set the torque

setting method.

0: Torque control is invalid

1: Keypad setting torque (

P03.12

)

2: AI1

3: AI2

4: AI3

5: Pulse frequency HDI

6: Multi-step torque

7: Modbus communication

–10: Reserved

Note

Setting

methods

–7,

100%

corresponds to 3 times of the rated motor

current.

○

P03.12

Torque set

through

keypad

Setting range: -300.0%

–300.0% (of the rated

motor current)

50.0%

○

P03.13

Torque

reference

filter time

0.000

–10.000s

0.100s

○

P03.14

Setting

source of

forward

rotation

upper-limit

frequency

in torque

control

0: Keypad (

P03.16

sets the value when

P03.14

=1;

P03.17

sets the value when

P03.15

=1)

1: AI1

2: AI2

3: AI3

4: Pulse frequency HDI

5: Multi-step setting

6: Modbus communication

–9: Reserved

Note:

Setting

methods

–9,

100%

corresponds to the maximum frequency.

○

P03.15

Setting

source of

reverse

rotation

upper-limit

○

Summary of Contents for GD20-004G-2












































































































































































Search results

Summary of Contents for GD20-004G-2

Reviews:

Brands by name

Popular brands

FOTEK GD20-004G-2, Operation Manual

Search results

Summary of Contents for GD20-004G-2

Reviews:

Brands by name

Popular brands