Forum SSW 40 Operating Instructions Manual Download Page 80 | Manualshive

Page: 80 / 88

Forum SSW 40 Operating Instructions Manual Download Page 80

Operation Maintenance Manual

Safety Spinning Wrench

PN 9GV73109-D - Revision: 02 2018-05

80

ST

O

R

A

G

E /

D

ISP

O

SA

L

7

Storage / Disposal

This chapter deals with procedures to be taken to the
storage after the decommissioning of the SSW-40. The
aim is to protect the machine, the environment and
people from damages. Therefore FORUM Handling Tools
recommends to read and implement the following
procedure accurately.

7.1

Storage of the entire device

Storage procedure

1. Clean the Safety Spinning Wrench. FORUM Handling Tools recommends

the use of a high pressure cleaner.

2. Store the machine on a pallet located on an even, supporting surface.

Observe the weight specifications in the technical data.

3. Ensure that the machine is stored so that no one can be injured by

moving parts or sharp edges.

4. Secure the machine with tensioning cables or in another manner to

prevent it from slipping or tipping when moved.

5. Grease the Safety Spinning Wrench as described in chapter “Lubrication”.
6. Conserve all not painted metal surfaces. FORUM Handling Tools

recommends the use of a lubricant or Tectyl.

» These surfaces should be checked periodically to be sure that no corrosion

has occurred.

7. Protect the machine against water penetration with a plastic tarp.
8. If stored for more than three months, bleed the pneumatic lines.

Intermediate Storage

Protection of tools

• Apply lubricant to all bare surfaces
• Protect all other bare surfaces with Tectyl Type 864 or an

equivalent agent.

• Place SSW-40s only on surrounded pallets and secure them with

tensioning cables and anti-slip mat.

Ambient Conditions

• Store in dry surroundings (maximum humidity 80%).

Longer Storage

Protection of tools

•  Dismantle the pneumatic cylinder and all pneumatic hoses.
•  Apply lubricant to all bare surfaces
•  Protect all other bare surfaces with Tectyl Type 864 or an

equivalent agent.

• Place SSW-40s only on surrounded pallets and secure them with

tensioning cables and anti-slip mat.

• Protect the SSW-40 against water penetration with a plastic tarp.

Ambient Conditions

• Store in dry surroundings (maximum humidity 80%).

«
...
78
79
80
81
82
...
»

Summary of Contents for SSW 40

























































































Reviews:

No comments