manualshive.com logo in svg

Forum SSW 40, Operating Instructions Manual, Page: 36 / 88

Share
Download
Forum SSW 40 Operating Instructions Manual Download Page 36

Operation Maintenance Manual

 

Safety Spinning Wrench  

 PN 9GV73109 - Revision: 02 2018-05

36

TR

A

N

SP

O

RT/

 

IN

STA

LL

AT

IO

N

3.2 

Transport

 DANGER

Suspended load!

The falling load can cause severe, even 
lethal injuries.

 

» NEVER stand beneath or in the 

swing area of lifted loads.

WEAR PROTECTIVE HELMET!

WEAR PROTECTIVE GLOVES!

WEAR SAFETY SHOES!

INFO

Safe Lifting Points!

 

- Lifting point locations, especially bores for 

load hooks are marked on the SSW-40. 

•  Make Sure all load hooks are fully installed in 

the lifting point

 

» Thus, the safe transport of 

FORUM Handling Tools

 

equipment is 

ensured.

INFO

Internal transport on site!

•  FORUM Handling Tools recommends to use 

pallets for longer component transports.

 

» Use a pallet for transport.

Principles for transport

1.  Ensure that transport routes are sufficiently 

dimensioned and marked.

 

» Ensure that persons are aware that transport is taking 

place.

2.  Always use pallets for longer transport distances.
3.  The total weight (object to be trans means 

of transport, e.g. forklift) must not exceed the 
supporting capacity of the subsurface.

4.  Ensure that such work is performed only by 

sufficiently qualified personnel.

5.  Always shut off SSW-40 before transport and secure 

against starting back up unintentionally.

 

» Start de-installation only after residual energy has 

been dissipated.

6.  Ensure that visual and audio contact exists between 

the crane operator and operating personnel.

7.  Secure the area against unauthorized entry. 

 

» If necessary, mark the area with information signs to 

warn of maintenance and repair work.

8.  Secure moving parts in suitable manner.
9.  Use only approved slinging and transport 

equipment, which is in perfect condition and 
suitable for the intended purpose. 

 

» Observe specified load limits.

10.  Secure SSW-40 against Slipping/sliding. 

 

» Observe SSW-40 weight. 

 

» Observe center of gravity.

11.  Never stand under suspended loads.
12.  Transport the SSW-40 carefully. 

 

» Do not fasten, lift or pull SSW-40 on parts that could 

be damaged. 

 

» Avoid sudden stops.

13.  Always use hoisting equipment (slings, hoisting 

cables, shackles, etc.), which has been inspected and 
is sufficiently dimensioned. 

14.  Ensure that all installation and hoisting procedures 

are accomplished in compliance with recognized 
rules of practice and industrial standards.

Summary of Contents for SSW 40

























































































Reviews:

No comments