manualshive.com logo in svg

Forum SSW 40, Operating Instructions Manual, Page: 29 / 88

Share
Download
Forum SSW 40 Operating Instructions Manual Download Page 29

Operation Maintenance Manual 

2018-05 

PN 9GV73109 - Revision: 02 

Safety Spinning Wrench 

29

SA

FE

TY

2.5 

Safety Precautions against 
Remaining Hazards

This machine was designed and produced according to the 
state-of-the-art in consideration of the safety precautions 
specified in EC Directive 2006/42/EC on Machinery.
The machine may be used only for:

 

- Its intended purpose („1 DESCRIPTION“).

 

- When it is in a technically safe state.
Nevertheless, it is not possible to exclude completely all 
hazardous situations, which could arise when the machine 
is used. Reference is made to these remaining risks at the 
beginning of each chapter and at the corresponding points 
in the description and measures for avoiding these risks are 
explained.

 WARNING

Mechanically generated sparks!

In the processing of incidents such as 
clamping components, metal tools can 
generate aparks. 

 

» The use of metallic hammers in 

hazardous areas has therefore 
be prohibited by the operating 
company.

 

» For loosening of clamping 

components only nonmetallic 
(plastic) hammer, which are 
approved for use in hazardous 
areas, may be used.

INFO

The operating company is responsible for 
ensuring that all personnel working on the 
machine is familiar with the remaining risks and 
observe the appropriate safety precautions.

 CAUTION

Never operate the SSW-40 without 
the Snub Line Sensor.

2.5.1 

Danger of Pinching/Crushing

 WARNING

Danger of pinching/crushing 
hands!

Moving parts pose a hazard during 
assembly, set-up and conversion work 
as well as during operation.

 

» NEVER reach between moving 

components.

 WARNING

Danger of pinching/crushing feet!

Moving parts pose a hazard during 
assembly, set-up and conversion work 
as well as during operation.

 

» NEVER stand below moving 

components.

 WARNING

Danger of pinching/crushing body!

Moving parts pose a hazard during 
assembly, set-up and conversion work 
as well as during operation.

 

» NEVER stand between moving 

components.

During assembly, set-up and conversion work as well as 
during operation pinching/crushing hazards can be posed 
by:

 

- Clamping and Unclamping the SSW-40,

 

- Installing the SSW-40 to Hanger and Backup line,

 

- Lifting and putting down components,
Pay attention to hands, feet and body when performing 
the work specified. Always ensure that no one is in a 
hazardous position.
Always wear your personal protective equipment.

Summary of Contents for SSW 40

























































































Reviews:

No comments