manualshive.com logo in svg

Forum 755000, Operating Instructions Manual

Share
Download
Forum 755000 Operating Instructions Manual Download Page 67

Operation Maintenance Manual 

06-2018 

PN 757000-D - Revision: 17 (up to SN 138212) Power Slip PS-500 

67

C

O

M

M

IS

SION

IN

G

 /

O

PE

R

A

TION

4.1.5 

Commissioning Checklist 

FORUM Handling Tools strongly recommends to accomplish the commissioning with the  
FORUM Handling Tools Commissioning Service.

Prior to use of the FORUM Handling Tools following checks must be carried out :

OK

Operating personnel is aware of all dangers regarding handling the FORUM Handling Tools PS-500 and 
its additional equipment.

OK

The entire operating personnel went through the OMM.

Check Installation and Lubrication

OK

PS-500 and all additional components are installed as shown in chapter 3.

OK

The Installation Checklist has been filled out completely. No fields are left blank and no fields have the 
status NOK.

OK

All parts, components (lifting equipment, etc.) not required for the actual operation have been removed.

OK

There are no people in the working area.

OK

All assemblies, parts, areas and surfaces, which have to be lubricated, are lubricated.

Hydraulic Characteristics

OK

Operating pressure.

160 bar (2320 PSI) - 210 bar (3046 PSI) 

OK

Volumetric flow.

18.9 l/min (5 GPM) - 37.85 l/min (10GPM)

OK

Min. required hydraulic Oil clearness.

NAS 7

OK

Correct Hydraulic connection/line arrangement.

OK

Automatic lubrication system has been connected to the PS-500.

Function Test 

OK

HCGS centers the pipe prior setting the Slip Assembly [if applicable].

OK

Slip Assembly is set after supplying pressure to connection "A". 
Feedback signal appears.

OK

HCGS opens automatically after setting the Slip Assembly [if applicable].

OK

Slip Assembly is raised after supplying pressure to connection "B". 
Feedback signal appears.

OK

Slip Assembly remains in raised position by a pressure drop to connection "B".

OK

One greasing cycle has been manually activated and finished.

OK

Grease is coming out of bores.

OK

Automatic grease function adjusted (5 sec. of greasing after 10 cycles).

Info

This commissioning Checklist contains only 
essential points and main contents of an internal 
commissioning. Check at least the mentioned 
points on your PS-500. For further questions or 
complete Commissioning Checklists (templates), 
please contact the Technical Support from 
FORUM Handling Tools.

Summary of Contents for 755000



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands