Ford VSS Manual Download Page 48

Page: 48 / 89

2013

Fiesta

- Key Start

Vehicle Security 2

GENERAL PROCEDURES (Continued)

10. The LED must be ON for option

. If the LED

12. Press and release the Lock button on the trim

is illuminated no action is required. If the LED

switch.

is not illuminated press the unlock button and

The horn will honk 1 time indication the system

verify the LED illuminates.

has entered the option 1 of the second program
bank.

11. Press and release the override button. The horn

will honk 5 times indicating the system has

13. The LED must be ON for option 1. If the LED

entered the second option bank.

is illuminated no action is required. If the LED
is not illuminated press the Unlock button and
verify the LED illuminates.

14. The

VSS

module is now programmed.

Page 2 of 2

SK9L2J-19G364-AA

FoMoCo

Summary of Contents for VSS


























































































Search results

Summary of Contents for VSS

Reviews:

Related manuals for VSS

Brands by name

Popular brands

Ford VSS, Manual

Search results

Summary of Contents for VSS

Reviews:

Related manuals for VSS

Brands by name

Popular brands