Ford VSS Manual Download Page 38

Page: 38 / 89

INSTALLATION

Vehicle Security

Fiesta - Key Start

NOTICE:
Vehicle Security systems are only applicable to vehicles with RKE.

1. Verify correct kit number.

Review VSS Installation Kit Contents

NOTE:

Kits are vehicle specific and are not interchangeable.

2. Review the VSS kit contents.

Vehicle Security System (VSS) Kit

QUANTITY

DESCRIPTION

MODULE ASSEMBLY

VSS SOFTWARE CARTRIDGE ASSEMBLY

WIRING HARNESS WITH 24-WAY

CONNECTOR

WIRING HARNESS WITH 10-WAY

CONNECTOR

INSTALLATION PARTS BAG

FUSE PARTS BAG

OPERATORS INSTRUCTIONS

VEHICLE SECURITY SYSTEM WARNING.

WINDOW DECAL

Module Preparation

3. Place the supplied fuses into the power distribution block on the VSS control module.

• Move the polarity jumpers to their proper locations on the control module, see illustration.

201

Fiesta - Key Start

Vehicle Security

Page 1 of 9

SK9L2J-19G364-AA

FoMoCo

Summary of Contents for VSS


























































































Search results

Summary of Contents for VSS

Reviews:

Related manuals for VSS

Brands by name

Popular brands

Ford VSS, Manual

Search results

Summary of Contents for VSS

Reviews:

Related manuals for VSS

Brands by name

Popular brands