Ford VSS Manual Download

Page: 79 / 89

15. Connect the Tan/Black wire from the T-harness to the Green/White horn circuit wire at BCM

Connector C2280G Pin 18.

LED Mounting

16. Keep the following points in mind when routing or positioning the LED for mounting:

• Have at least 3/4" clearance behind trim panels for the wiring harness to be routed.

• The LED should be clearly visible from the driver's side window when mounted.

• Do not mount the LED on trim panels that cover air bags.

17. Mount the LED at an appropriate location on the upper steering column shroud, using the guidelines

listed above.

• Drill a 9/32" hole into the selected location, for the LED to mount in.

18. Route the LED wire harness to the VSS module.

19. Connect the LED wire harness to the VSS module.

• Secure the LED wire harness with tie-straps.

INSTALLATION (Continued)

2013 Fusion

Vehicle Security

Page 7 of 10

SK9L3Z-19G361-AA

Summary of Contents for VSS


























































































Search results

Summary of Contents for VSS

Reviews:

Related manuals for VSS

Brands by name

Popular brands

Ford VSS, Manual

Search results

Summary of Contents for VSS

Reviews:

Related manuals for VSS

Brands by name

Popular brands