Fisherbrand 15409709 Instruction Manual Download Page 51

Page: 51 / 57

www.eu.fishersci.com/fisherbrand

5 BASIC TROUBLESHOOTING

Problem

Possible Cause

Solution

System Inactive
(pump and the
control panel not
operating)

No electrical power

Ensure the power cord is
connected to a live power
source

Main fuse blown.

Replace the main fuse

RO Indicator Light
Blinks

Inlet water exceeds

Add additional pretreatment

RO Membrane damaged

Replace the RO membrane

UP Indicator Light
Blinks

UP cartridges exhausted

Replace AccuDuo H and U
Pack cartridges

Low Pressure Alarm

No inlet water

Check tap water faucet

Prefilter clogged

Replace prefilters in the
Prefiltration pack

Pressure at the tap water
too low

Call service to have an external
booster pump installed by a
professional engineer

No Water

Water supply stopped

Restore water supply

Water tank is empty

Wait until water tank is filled

RO water failure

Wait till RO water passes
quality parameter.
If RO indicator light blinks for a
long period of time, then RO
membrane needs to be
replaced.

Booster Pump not working Contact a ULS agent

Prefilter clogged

Replace prefilters in the
Prefiltration pack.

Summary of Contents for 15409709


























































Search results

Summary of Contents for 15409709

Reviews:

Related manuals for 15409709

Brands by name

Popular brands

Fisherbrand 15409709, Instruction Manual

Search results

Summary of Contents for 15409709

Reviews:

Related manuals for 15409709

Brands by name

Popular brands