Festo Soft Stop SPC11 Series System Manual Download

Page: 64 / 134

4. Commissioning

4-4

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

4.1.1 Basic principles of configuring and operating the SPC11

Parameters

The SPC11 must be familiar with certain conditions of use.
These conditions of use are described by the three following
parameters:

Parameters

Description

mplification stage

Influences the acceleration behaviour of the
drive.

ushioning stage

Influences the retracting behaviour when
moving to the end positions and intermedi-
ate positions.

ystem parameter

Characteristic value for the structure of the
drive.

The parameters can be entered:

– Before commissioning (pre-parametrizing without drive in

the office).

– When commissioning.

Summary of Contents for Soft Stop SPC11 Series







































































































































Search results

Summary of Contents for Soft Stop SPC11 Series

Reviews:

Related manuals for Soft Stop SPC11 Series

Brands by name

Popular brands

Festo Soft Stop SPC11 Series, System Manual

Search results

Summary of Contents for Soft Stop SPC11 Series

Reviews:

Related manuals for Soft Stop SPC11 Series

Brands by name

Popular brands