manualshive.com logo in svg

Festo Soft Stop SPC11 Series, System Manual

Share
Download
Festo Soft Stop SPC11 Series System Manual Download Page 76

4. Commissioning

4-16

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

The permitted values of the parameters for the drive you are
using can be found in the appropriate axis-specific supple-
ment. The currently set values will be shown briefly when the
operating voltage is switched on (see also Fig. 4/2).

If the SPC11 is in the status as at delivery:

When the operating voltage is switched on the SPC11 waits
for the amplification stage (A) to be entered.

S

In this case, set the parameters as described in section
4.2.

If the parameters have already been set:

When the operating voltage is switched on the SPC11 shows
briefly the set parameters one after the other, so that they can
be checked. The SPC11 then indicates readiness to carry out
the teach procedure (t flashes).

(The t flashes.)

The teach procedure can now be started (see sections 4.3.2).

Summary of Contents for Soft Stop SPC11 Series







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands