manualshive.com logo in svg

Festo Soft Stop SPC11 Series, System Manual

Share
Download
Festo Soft Stop SPC11 Series System Manual Download Page 83

4. Commissioning

4-23

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

Overview of the commissioning sequence on the
SPC11

Set the parameters and start the automatic teach procedure
(SPC11 in status as at delivery)

Switching on

Set

system parameters

Set

amplification stage

Set

cushioning stage

Set the value with +/- .

Conclude entry with

Enter.

The SPC11 waits for the

teach task

Pre-commissioning

is concluded.

The teach task can

be started.

The teach procedure

is carried out

The teach task is concluded successfully.

The mass will be

pressed against the

end position.

O1 supplies a 1-signal.

P.03 and P.04 can be

taught (see next page).

The t flashes.

The dots flash.

Enter button

Enter button

Enter button

Teach button/input

Firmware version number

Display of

firmware version

Wait approx. 0.5 second

Fig. 4/3: Set the parameters and start the teach procedure

Summary of Contents for Soft Stop SPC11 Series







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands