Festo EMCS-ST Operating Instructions Manual Download Page 5

Page: 5 / 86

Repair............................................................................................................................64

IO-Link..........................................................................................................................64

14.1

Device description file IODD......................................................................................... 64

14.2

IO-Link parameters....................................................................................................... 64

14.2.1

Identification parameters........................................................................................65

14.2.2

Device data............................................................................................................. 67

14.2.3

Process data........................................................................................................... 72

14.2.4

System parameters.................................................................................................75

14.2.5

Control end-to-end operation via IO-Link................................................................ 76

14.2.6

Monitor end-to-end operation via IO-Link............................................................... 77

Disassembly................................................................................................................ 77

Disposal........................................................................................................................78

Technical data............................................................................................................. 78

17.1

Technical data, general................................................................................................. 78

17.2

Technical data, electrical.............................................................................................. 81

17.2.1

Power supply.......................................................................................................... 81

17.2.2

Digital inputs (DI)....................................................................................................82

17.2.3

Digital outputs (DO)................................................................................................83

17.2.4

IO-Link.................................................................................................................... 83

17.2.5

Motor (integrated).................................................................................................. 84

17.2.6

Rotary encoder (integrated).................................................................................... 84

17.2.7

Temperature sensor (integrated)............................................................................ 85

Festo — EMCS-ST — 2020-04a

Summary of Contents for EMCS-ST






















































































Search results

Summary of Contents for EMCS-ST

Reviews:

Related manuals for EMCS-ST

Brands by name

Popular brands

Festo EMCS-ST, Operating Instructions Manual

Search results

Summary of Contents for EMCS-ST

Reviews:

Related manuals for EMCS-ST

Brands by name

Popular brands