Festo EMCS-ST Operating Instructions Manual Download Page 4

Page: 4 / 86

Commissioning "DIO operation (digital I/O)"................................................................ 24

Commissioning "IO-Link Operation"............................................................................. 27

Drive system.................................................................................................................28

11.1

Dimensions and units.................................................................................................... 28

11.1.1

Basic and user units............................................................................................... 28

11.1.2

Dimension reference system.................................................................................. 29

11.2

Controller...................................................................................................................... 31

11.2.1

Firmware................................................................................................................ 31

11.2.2

Factory settings..................................................................................................... 31

11.2.3

Switch-on behaviour.............................................................................................. 31

11.2.4

Switch-off behaviour.............................................................................................. 32

11.2.5

Restart................................................................................................................... 34

11.2.6

Master control....................................................................................................... 39

11.3

Operating modes...........................................................................................................41

11.3.1

Dynamic state change............................................................................................ 41

11.3.2

Homing.................................................................................................................. 41

11.3.2.1

Function................................................................................................................. 42

11.3.2.2

Parameter.............................................................................................................. 43

11.3.2.3

Timing.................................................................................................................... 44

11.3.3

Single end-to-end operation.................................................................................. 46

11.3.3.1

Function................................................................................................................. 46

11.3.3.2

Parameter.............................................................................................................. 47

11.3.3.3

Timing.................................................................................................................... 47

11.3.4

End-to-end operation with press function.............................................................. 51

11.3.4.1

Function................................................................................................................. 51

11.3.4.2

Parameter.............................................................................................................. 52

11.3.4.3

Timing.................................................................................................................... 53

11.3.5

Manual operation (demo)...................................................................................... 57

11.3.5.1

Function................................................................................................................. 57

11.3.5.2

Parameter.............................................................................................................. 57

11.3.5.3

Timing.................................................................................................................... 58

Maintenance and care.................................................................................................. 59

Diagnostics and malfunctions...................................................................................... 59

13.1

Diagnostics via LED displays......................................................................................... 59

13.1.1

LED "C/Q" (communication and device status)..................................................... 59

13.1.2

LED display "Menu".............................................................................................. 60

13.1.3

LED display "Parameter"....................................................................................... 61

13.2

Diagnostic messages.....................................................................................................61

13.2.1

Acknowledge error................................................................................................. 61

13.2.2

Diagnostic messages and fault clearance.............................................................. 62

Festo — EMCS-ST — 2020-04a

Summary of Contents for EMCS-ST






















































































Search results

Summary of Contents for EMCS-ST

Reviews:

Related manuals for EMCS-ST

Brands by name

Popular brands

Festo EMCS-ST, Operating Instructions Manual

Search results

Summary of Contents for EMCS-ST

Reviews:

Related manuals for EMCS-ST

Brands by name

Popular brands