Festo EMCS-ST Operating Instructions Manual Download Page 64

Page: 64 / 86

13.3

Repair

Repair or maintenance of the product is not permissible. If necessary, replace the complete product.
–

In case of an internal defect: replace the product.

–

Send the defective product unchanged with a description of the fault and application to Festo for
analysis.

–

Check with your regional Festo contact person to clarify the conditions for the return shipment.

IO-Link

14.1

Device description file IODD

The boot time of the integrated drive EMCS-ST is 1 s and deviates from the IO-Link specification.

Depending on the drive system, device description files (IODD files) are available for configuring the
integrated drive EMCS-ST in IO-Link operation.

Drive system

IODD file name

Linear

EGSS-BS

Mini slide unit

Festo-EGSS-BS-...-IODD1.1.xml

ELGE-TB

Toothed belt axis unit

Festo-ELGE-TB-...-IODD1.1.xml

ELGS-BS

Spindle axis unit

Festo-ELGS-BS-...-IODD1.1.xml

ELGS-TB

Toothed belt axis unit

Festo-ELGS-TB-...-IODD1.1.xml

EPCE-TB

Electric cylinder unit

Festo-EPCE-TB -...- IODD1.1.xml

EPCS-BS

Electric cylinder unit

Festo-EPCS-BS -...- IODD1.1.xml

Rotary

ERMS

Rotary drive unit

Fixed ERMS-...-IODD1.1.xml

Tab. 32 Device description file IODD

The current device description files are available on the Festo Support Portal

www.festo.com/sp.

14.2

IO-Link parameters

The following parameter groups are available for configuration and operation of the integrated drive in
an IO-Link network:
–

Identification parameters: IDs, version numbers, …

14.2.1 Identification parameters

–

Device data: setpoint and actual values, limit values, …

14.2.2 Device data

–

Process data: commands, status information, …

14.2.3 Process data

–

System parameters: control functions for application software,

14.2.4 System parameters

–

Diagnostic data: device status,...

14.2.2 Device data

IO-Link

Festo — EMCS-ST — 2020-04a

Summary of Contents for EMCS-ST






















































































Search results

Summary of Contents for EMCS-ST

Reviews:

Festo EMCS-ST, Operating Instructions Manual, Page: 64 / 86

Search results

Summary of Contents for EMCS-ST

Reviews: