Festo EMCS-ST Operating Instructions Manual Download Page 75

Page: 75 / 86

14.2.4

System parameters

The system parameters contain all command data (e.g. start and stop, power stage control, ...) dis-
played as buttons in the application software interface to control the drive system.

Index.
Subindex

Name

Description

Data type
(length)

User access

U = User
M = Maintenance
personnel
S = Specialist

System commands for con-
trolling the drive unit

Value 0xC8 (200) execute Mov

–

Control command for execut-
ing the motion "Mov

" to

the "Lim

("Ref")” end posi-

tion

14.2.5 Control end-to-end

operation via IO-Link.

Value 0xC9 (201) execute Mov

Out

–

Control command for execut-
ing the motion "Mov

Out

" to

the "Lim

Out

" end position

14.2.5 Control end-to-end

operation via IO-Link.

Value 0xCA (202) Stop motion
–

Control command for stop-
ping travel.

14.2.5 Control end-to-end

operation via IO-Link.

0x0002.0
(2.0)

SystemCom-
mand

Value 0xCB (203) Disable power
stage
–

Control command for switch-
ing off the power stage.

14.2.5 Control end-to-end

operation via IO-Link.

UIntegerT
(1 byte)

–

0x0002.0
(2.0)

SystemCom-
mand

Value 0xCC (204): Enable power
stage

UIntegerT
(1 byte)

–

IO-Link

Festo — EMCS-ST — 2020-04a

Summary of Contents for EMCS-ST






















































































Search results

Summary of Contents for EMCS-ST

Reviews:

Festo EMCS-ST, Operating Instructions Manual, Page: 75 / 86

Search results

Summary of Contents for EMCS-ST

Reviews: