manualshive.com logo in svg

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 99 / 233

Share
Download
Fayat Dynapac CC1100 VI Instruction Manual Download Page 99

Miscellaneous

4812164501.pdf

2021-05-06

Miscellaneous

Lifting

1

2

3

4

Fig. Articulation in the locked position
1. Locking arm
2. Locking pin
3. Locking stud
4. Locking lug

Locking the articulation

Articulation must be locked to prevent inadvertent
turning before lifting the roller.

Articulation must be locked to prevent inadvertent
turning before lifting the roller.

Turn the steering wheel to the straight ahead position.
Enable the parking brake.

Pull out the locking pin (2) fitted with a wire, and pull
up/out the locking dowel (3).

Fold out the locking arm (1) and secure it to the upper
locking lug (4) on rear frame.

Fit the locking stub (3) in the holes through the locking
arm (1) and locking lug (4) and secure the stud in
position with the locking pin (2).

85

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments