manualshive.com logo in svg

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 198 / 233

Share
Download
Fayat Dynapac CC1100 VI Instruction Manual Download Page 198

Maintenance - 2000h

4812164501.pdf

2021-05-06

Check - Coolant system

1

Fig. Cooling water container
(CC1100/C VI -  CC1200/C VI)
 1. Filler cap

Check that all hoses/hose connectors are intact and
tight. Fill with coolant as specified in the lubricants
specification.

Take great care when opening the radiator cap
while the engine is hot. Wear protective gloves and
goggles.

Take great care when opening the radiator cap
while the engine is hot. Wear protective gloves and
goggles.

Also check the freezing point. Change the coolant
every other year.

Also check the freezing point. Change the coolant
every other year.

Fig. Cooling water container
(CC1300/C VI -  CC1400/C VI)
 1. Filler cap

1

Air cleaner
Check - Replacement of main filter

Replace the air cleaner's main filter when the
indicator shows red. The  indicator is located on
the filter, or in its immediate vicinity.

Replace the air cleaner's main filter when the
indicator shows red. The  indicator is located on
the filter, or in its immediate vicinity.

184

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments