Home
/
Fayat
/
Dynapac CC1100 VI
/
Instruction Manual

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 156 / 233

Share

Page: 156 / 233

Fayat Dynapac CC1100 VI Instruction Manual Download Page 156

Maintenance measures - 250 h

4812164501.pdf

2021-05-06

Air cleaner
- Cleaning

Fig. Air cleaner
2. Cover
5. Filter housing

2

5

Wipe the inside of the cover (2) and filter housing (5).

Wipe clean on both sides of the outlet
pipe.

Outer edge of outlet
pipe.

Inner edge of
outlet pipe.

Wipe also both surfaces for the outlet pipe; see
adjacent figure.

Check that the hose clamps between the filter
housing and the suction hose are tight and that
the hoses are intact. Inspect the entire hose
system, all the way to the engine.

Check that the hose clamps between the filter
housing and the suction hose are tight and that
the hoses are intact. Inspect the entire hose
system, all the way to the engine.

142

«
...
154
155
156
157
158
...
»

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments