manualshive.com logo in svg

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 27 / 233

Share
Download
Fayat Dynapac CC1100 VI Instruction Manual Download Page 27

Special instructions

4812164501.pdf

2021-05-06

Battery handling

When removing batteries, always disconnect the
negative cable first.

When removing batteries, always disconnect the
negative cable first.

When fitting batteries, always connect the
positive cable first.

When fitting batteries, always connect the
positive cable first.

Dispose of old batteries in an environmentally
friendly way. Batteries contain toxic lead.

Dispose of old batteries in an environmentally
friendly way. Batteries contain toxic lead.

Do not use a quick-charger for charging the
battery. This may shorten battery life.

Do not use a quick-charger for charging the
battery. This may shorten battery life.

Jump starting

Do not connect the negative cable to the
negative terminal on the dead battery. A spark
can ignite the oxy-hydrogen gas formed
around the battery.

Do not connect the negative cable to the
negative terminal on the dead battery. A spark
can ignite the oxy-hydrogen gas formed
around the battery.

Check that the battery used for jump starting
has the same voltage as the dead battery.

Check that the battery used for jump starting
has the same voltage as the dead battery.

Fig. Jump starting

1

2

3

4

Turn the ignition and all power consuming equipment
off. Switch off the engine on the machine which is
providing jump start power.

First connect the jump start battery's positive terminal
(1) to the flat battery's positive terminal (2).Then
connect the jump start battery's negative terminal (3)
to, for example, a bolt (4) or the lifting eye on the
machine with the flat battery.

Start the engine on the power providing machine. Let it
run for a while. Now try to start the other machine.
Disconnect the cables in the reverse order.

13

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments