manualshive.com logo in svg

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 44 / 233

Share
Download
Fayat Dynapac CC1100 VI Instruction Manual Download Page 44

Machine description

4812164501.pdf

2021-05-06

Machine plate

1

Fig. Operator platform
     1. Machine plate

The machine type plate (1) is affixed on the rear left
edge of the frame.

The plate includes:

• name and address of the manufacturer (2)

• type of machine (3)

• PIN-product identification number (serial number) (4)

• maximum weight (5)

• service weight (6)

• engine power (7)

• year of manufacture (8)

If the machine is delivered outside of the EU, the plate
may not have a CE marking and the year of
manufacture.

2

3

4

5

6

7

8

Please state the machine's PIN (serial number)
when ordering parts.

Engine plates

The engine's type plate (1) is located on top of the
cylinder head cover.

The plate specifies the type of engine, its serial
number and the engine specification.

30

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments