Home
/
Fayat
/
Dynapac CC1100 VI
/
Instruction Manual

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 104 / 233

Share

Page: 104 / 233

Fayat Dynapac CC1100 VI Instruction Manual Download Page 104

Miscellaneous

4812164501.pdf

2021-05-06

Short distance towing with switched off engine

Fig. Propulsion pump (CC1100/C VI -
CC1200/C VI)
1. Bypass screw

1

Chock the drums to prevent the roller from
moving.

Chock the drums to prevent the roller from
moving.

Open the hood and make sure that the propulsion
pump is accessible.

There is a bypass screw (1) located on the pump that
must be unscrewed counterclockwise (max two turns),
to put the drive system (ports A and B) in bypass
mode.

This function enables a machine to be moved without
the drive shaft on the propulsion pump rotating.

Turn the bypass screw (1) clockwise to reset.

Fig. Propulsion pump (CC1300/C VI -
CC1400/C VI)
1. By-pass screw

1

90

«
...
102
103
104
105
106
...
»

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments