manualshive.com logo in svg

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 139 / 233

Share
Download
Fayat Dynapac CC1100 VI Instruction Manual Download Page 139

Maintenance, 10h

4812164501.pdf

2021-05-06

Fuel tank - Filling

Fig.  Fuel tank
     1. Filler cap

1

Refuel the tank every day before starting work.

Open the engine hood, unscrew the tank cap (1) fill
with diesel up to the lower edge of the filler pipe.

Tier 4f and Stage V Kubota engines require the
use of Ultra Low Sulphur Diesel (ULSD) fuel,
which has a sulphur content of 15 ppm (parts per
million) or less. Higher sulphur contents cause
operating problems and put the useful life of
components at risk, which can lead to engine
trouble.

Tier 4f and Stage V Kubota engines require the
use of Ultra Low Sulphur Diesel (ULSD) fuel,
which has a sulphur content of 15 ppm (parts per
million) or less. Higher sulphur contents cause
operating problems and put the useful life of
components at risk, which can lead to engine
trouble.

Stop the diesel engine. Short-circuit (press) the
filler gun against a non-insulated part of the roller
before refuelling, and against the filler pipe while
refuelling.

Stop the diesel engine. Short-circuit (press) the
filler gun against a non-insulated part of the roller
before refuelling, and against the filler pipe while
refuelling.

Never refuel while the engine is running. Do not
smoke and avoid spilling fuel.

Never refuel while the engine is running. Do not
smoke and avoid spilling fuel.

The fuel tank holds

CC1100/C VI - CC1200/C VI:      46 liters     (48.6 qts)

CC1300/C VI - CC1400/C VI:      60 liters     (63.4 qts)

Water tank - Filling

Fig. Water tank
     1. Tank cap

1

Unscrew the tank cap (1) and fill with clean water.
Do not remove the strainer. See technical
specifications for the tank volume.

Unscrew the tank cap (1) and fill with clean water.
Do not remove the strainer. See technical
specifications for the tank volume.

Only additive: A small amount of
environment-friendly antifreeze.

Only additive: A small amount of
environment-friendly antifreeze.

125

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments