manualshive.com logo in svg

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 94 / 233

Share
Download
Fayat Dynapac CC1100 VI Instruction Manual Download Page 94

Operation

4812164501.pdf

2021-05-06

Switching off

32

1

2

31

22

9

Fig. Instrument panel
 1. Ignition key
 2. Throttle control (D1703/V2203-M-E3B)
 9. Instrument cover
 22. Panel for warning lamps
 31. Parking brake
 32. Engine speed selector
(D1803/V2403-CR-E4B/V2403-CR-E5B)

Activate the parking brake (31).

D1703 / V2203-M-E3B

Turn the engine speed control (2) back to idling.

D1803 / V2403-CR-E4B / V2403-CR-E5B

Press the LED button (32) so it is set to LOW mode
(left LED lit).

Allow the engine to idle for a few minutes to cool down.

Check instruments and warning lamps to see if any
faults are indicated. Switch off all lights and other
electrical functions.

Turn the ignition key (1) to the left to the switched off
position. At the end of the shift, fold over the
instrument cover (9) and lock.

80

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments