manualshive.com logo in svg

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 145 / 233

Share
Download
Fayat Dynapac CC1100 VI Instruction Manual Download Page 145

Maintenance, first 50h

4812164501.pdf

2021-05-06

Maintenance, first 50h

Park the roller on a level surface.
The engine must be switched off and the
parking brake activated when checking or
adjusting the roller, unless otherwise specified.

Park the roller on a level surface.
The engine must be switched off and the
parking brake activated when checking or
adjusting the roller, unless otherwise specified.

Ensure that there is good ventilation (air
extraction) if the engine is run indoors. Risk of
carbon monoxide poisoning.

Ensure that there is good ventilation (air
extraction) if the engine is run indoors. Risk of
carbon monoxide poisoning.

Engine oil and oil filter - Change

Fig. Engine compartment right side  -
D1703-E3B (Stage IIIA)
     1. Drain hose
     2. Drain plug
     3. Filler cap
     4. Oil filter

1

2

3

4

Run the engine until it is warm before draining the oil .

Switch off the engine and push in the emergency
stop.

Switch off the engine and push in the emergency
stop.

Take great care when draining fluids and oils.
Wear protective gloves and goggles.

Take great care when draining fluids and oils.
Wear protective gloves and goggles.

131

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments