manualshive.com logo in svg

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 220 / 233

Share
Download
Fayat Dynapac CC1100 VI Instruction Manual Download Page 220

Maintenance, 3000h

4812164501.pdf

2021-05-06

Replacing the fuel filter

1

Fig. Engine compartment, right side
     1. Fuel filter

Place a container underneath to collect fuel that
runs out when the filter is released.

Place a container underneath to collect fuel that
runs out when the filter is released.

Screw off the fuel filter (1). The filter is of the
disposable type and cannot be cleaned. Hand in to a
waste disposal site.

Install the new filter.

Start the engine and check that the fuel filter is tight.

Refer to the engine manual for detailed
instructions when replacing the fuel filter.

Refer to the engine manual for detailed
instructions when replacing the fuel filter.

Ensure good ventilation (air extraction) if the
diesel engine is run indoors. Risk of carbon
monoxide poisoning.

Ensure good ventilation (air extraction) if the
diesel engine is run indoors. Risk of carbon
monoxide poisoning.

Replacing the pre-filter

2

2

3

Fig. Engine compartment -
D1703-M-IDI-E3 (Stage IIIA) /
V2203-M-E3B (Stage IIIA)
     1. Pre-filter
     2. Hose clamps
     3. Fuel pump

1

Activate the parking brake.
Switch off the engine and open the engine hood.

Place a container underneath to collect fuel that
runs out when the filter is released.

Place a container underneath to collect fuel that
runs out when the filter is released.

206

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments