manualshive.com logo in svg

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 226 / 233

Share
Download
Fayat Dynapac CC1100 VI Instruction Manual Download Page 226

Maintenance, 3000h

4812164501.pdf

2021-05-06

Draining of water separator

1

Fig. Fuel filter
   1. Filter knob
   2. Filter element
   3. OFF
   4. ON

2

3

4

Close the fuel filter knob (1).

Remove the top cap and rinse the inside with diesel
fuel.

Remove filter element (2) and rinse the inside with
diesel fuel.

After cleaning, install the fuel filter, to keep out of dust
and dirt.

Air-bleed the injection pump.

Dust and dirt may cause a injection pump and
nozzle failure. Wash the fuel filter cup periodically.

Dust and dirt may cause a injection pump and
nozzle failure. Wash the fuel filter cup periodically.

Fig. Fuel filter element
   5. O-ring
   6. Filter element
   7. Spring
   8. Filter
   9. Screw ring

5

6

7

8

9

5

212

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments