manualshive.com logo in svg

Fayat Dynapac CC1100 VI, Instruction Manual, Page: 154 / 233

Share
Download
Fayat Dynapac CC1100 VI Instruction Manual Download Page 154

Maintenance measures - 250 h

4812164501.pdf

2021-05-06

Engine oil and oil filter - Change

Fig. Engine compartment right side  -
D1703-E3B (Stage IIIA)
     1. Drain hose
     2. Drain plug
     3. Filler cap
     4. Oil filter

1

2

3

4

Run the engine until it is warm before draining the oil .

Switch off the engine and push in the emergency
stop.

Switch off the engine and push in the emergency
stop.

Take great care when draining fluids and oils.
Wear protective gloves and goggles.

Take great care when draining fluids and oils.
Wear protective gloves and goggles.

Fig. Engine compartment, right side -
D1703-E4B (Tier 4f / Stage V)
     1. Drainage hose
     2. Drain plug
     3. Filler cap
     4. Oil filter

1

2

3

4

Place a receptacle that holds at least 12 liters (8 gal.)
under the drain plug (2).

Undo the oil filler cap  (3), and undo the drain plug (2)
in the end of the drain hose (1). Let all the engine oil
flow out.

Deliver the drained oil to special waste handling.

Deliver the drained oil to special waste handling.

Refer to the engine manual for detailed
instructions when changing oil and filters.

Refer to the engine manual for detailed
instructions when changing oil and filters.

140

Summary of Contents for Dynapac CC1100 VI










































































































































































































































Reviews:

No comments