manualshive.com logo in svg

Fayat Group DYNAPAC CC224HF, Instruction Manual

Share
Download
Fayat Group DYNAPAC CC224HF Instruction Manual Download Page 93

Operation

4812159601_H.pdf

2021-01-14

Washing the spreader

When corrosive material has been used the spreader
must be flushed clean with water.
This should also be done when the spreader is not to
be used for a long period.

Adjusting the chain 1

Loosen the four bolts for the bearing housing and turn
it to the correct position, where the chain has a
clearance of approx. 10 mm. Tighten the bolts.

Adjusting the chain 2

Loosen the two nuts, see arrows, for the bearing
housing and turn it to the correct position, where the
chain has a clearance of approx. 10 mm. Tighten the
nuts.

Lubrication

At the start of every season and after every 40 hours
of operation. Once per season is sufficient during
infrequent use.

Lubricate after every season before putting into
storage.

81

Summary of Contents for DYNAPAC CC224HF















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands