Fayat Group DYNAPAC CC224HF Instruction Manual Download Page 66

Page: 66 / 174

Machine description

4812159601_H.pdf

2021-01-14

"CALIBRATION"

- service personnel only, requires

password.

"EDC Calibration" used to calibrate the joystick and
speed potentiometer.

"TX Program" only used to change software in the
display and requires special equipment and know-how.

"EDC CALIBRATION"

To calibrate, move the joystick fully forward (F) and
press in both black buttons on the top of the joystick.
(See also manual W3025)

Continue in the same way with the other positions for
the joystick (N), (R) and the speed potentiometer.

Press the disk button to save the values.

"ABOUT"

It is also possible to see the version of the installed
software.

Summary of Contents for DYNAPAC CC224HF















































































































































































Search results

Summary of Contents for DYNAPAC CC224HF

Reviews:

Brands by name

Popular brands

Fayat Group DYNAPAC CC224HF, Instruction Manual

Search results

Summary of Contents for DYNAPAC CC224HF

Reviews:

Brands by name

Popular brands