Fayat Group DYNAPAC CC224HF Instruction Manual Download Page 81

Page: 81 / 174

Operation

4812159601_H.pdf

2021-01-14

Interlock

The roller is equipped with Interlock.

The diesel engine with switch off after 7 seconds if the
operator gets off the seat when going
forwards/backwards.

If the control is in neutral when the operator stands up
a buzzer will go on until the parking brake is activated.

If the parking brake is activated, the diesel engine will
not stop if the forward/reverse lever is moved out of
neutral.

The diesel engine will switch off immediately if for any
reason the forward/reverse lever is moved out of
neutral when the operator is not sitting down and the
parking brake has not been activated.

Sit down for all operations!

Summary of Contents for DYNAPAC CC224HF















































































































































































Search results

Summary of Contents for DYNAPAC CC224HF

Reviews:

Brands by name

Popular brands

Fayat Group DYNAPAC CC224HF, Instruction Manual

Search results

Summary of Contents for DYNAPAC CC224HF

Reviews:

Brands by name

Popular brands