manualshive.com logo in svg

Fayat Group DYNAPAC CC224HF, Instruction Manual

Share
Download
Fayat Group DYNAPAC CC224HF Instruction Manual Download Page 131

Maintenance - 50h

4812159601_H.pdf

2021-01-14

Maintenance - 50h

Every 50 hours of operation (Weekly)

Park the roller on a level surface.
The engine must be switched off and the
parking brake activated when checking or
adjusting the roller, unless otherwise specified.

Park the roller on a level surface.
The engine must be switched off and the
parking brake activated when checking or
adjusting the roller, unless otherwise specified.

Ensure that there is good ventilation (air
extraction) if the engine is run indoors. Risk of
carbon monoxide poisoning.

Ensure that there is good ventilation (air
extraction) if the engine is run indoors. Risk of
carbon monoxide poisoning.

Fuel filter - Draining

Figure.  Fuel filter
1. Drain plug
2. Hand pump

1

2

Unscrew the drain plug (1) at the bottom of the fuel
filter.

With the aid of the secondary hand-operated pump,
make certain that all sediment comes out. See
Cummins service manual.

Tighten the drain plug as soon as uncontaminated fuel
runs out.

119

Summary of Contents for DYNAPAC CC224HF















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands