evertz 3080UEP Series User Manual Download Page 53

Page: 53 / 62

3080UEP Series

Professional 3G/HD/SD Universal Contribution Encoding Platform

Revision 0.2

Page - 45

5.8.

IPTV ENCODER

Figure 5-11: WebEasy –IPTV Encoder

Output Configuration

IP Address:

This parameter allows the user to select a streaming output IP address for the IPTV

Encoder. Can be a Multicast or Unicast address.

UDP Port Number:

This parameter allows the user to select the destination UDP port number of the

streaming output.

TTL:

This parameter allows the user to set the TTL (Time To Live) field of the output IP packets.

Total TS Bit Rate:

This parameter allows the user to select the output TS Bitrate in kbps. The

3080UEP will automatically adjust the bitrate for video based on audio and other PID settings.

TS Encapsulation Type:

This parameter allows the user to select the output encapsulation type.

The options include UDP or RTP.

Summary of Contents for 3080UEP Series































































Search results

Summary of Contents for 3080UEP Series

Reviews:

Related manuals for 3080UEP Series

Brands by name

Popular brands

evertz 3080UEP Series, User Manual

Search results

Summary of Contents for 3080UEP Series

Reviews:

Related manuals for 3080UEP Series

Brands by name

Popular brands